Exactly How to Remove and Replace a Bath Tub.
Exactly How to Remove and Replace a Bath Tub.
Blog Article
We have stumbled on the article involving How to Install a Bathtub down the page on the net and figured it made perfect sense to relate it with you in this article.
Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is conveniently accessible, the job can move easily; if you have to open up a wall to get rid of the old tub and also position the brand-new bath tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and embeded in the new one. Make certain you have qualified on your own for the job and also are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed task, it is better to think about using one before you start. Chances are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new tub in your washroom if you have already gotten a brand-new tub as well as do not require to change the plan of your previous water pipes.
Your tools and also product checklist must consist of the following:
Preparing for the Installation
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted accessibility that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the tub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile tap port to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water system and also inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Load the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub must wait till the bathtub has been made use of at least once as this will resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in area between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous kind must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, bring about problems with moisture as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the movement experienced when the bathtub is in use. The sealer can crack relatively very early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub Yourself? Write feedback directly below. We would be delighted to hear your responses about this page. In hopes to see you back again in the near future. If you please take the opportunity to distribute this blog post if you enjoyed it. Bless you for your time. Please pay a visit to our website back soon.
Book A Service Call Report this page